PL Mount Modification Kit (Blackmagic Pocket Cinema Camera 6K / 6K G2 / 6K Pro) allows users to convert their BMPCC 6K, 6K G2, or 6K Pro camera to a PL Mount through a short modification process. All necessary tools are included in the kit. The PL Mount is made of stainless steel and aircraft grade aluminum and includes the PL port cap. Shims are provided with the kit for adjusting back focus and the appropriate shims are installed prior to shipping. Further adjustment should not be needed but can be checked using a wide angle lens and a focus chart. The BMPCC6K's own EF Mount screws are used to attach the PL Mount to the camera. The modification process can be reversed. If you choose to go back to EF mount in the future, you can do it by reversing steps in the process, however, switching back and forth will eventually strip the plastic in your camera as the sensor block is made of a composite plastic material (it is strong but still plastic). Important Note: The majority of modern, s35mm lenses are compatible, but lenses with a rear protrusion longer than 40mm, measured from the PL flange, are not compatible and other lenses may not fit due to the shape of the original Blackmagic 6K body design. Please review the diagram below to measure the protrusion requirements for fitting your lens into a modified BMPCC6K. If you are still unsure, you can check the BMPCC6K Compatible PL Lens Chart here . Includes: 1x Shim Set 1x Jeweler's Screwdriver 2x Strips of Flocking Tape Camera is not included. Shim Set (stackable to achieve necessary thickness): Silver .0127mm (0.0005") Amber .0254mm (0.001") Purple .0381mm (0.0015") Red .0508mm (0.002") Green .0762mm (0.003") Tan .1016mm (0.004") [ Installed] Blue .127mm (0.005") PL Mount Modification Kit (BMPCC6K) Installation Tutorial:

Unified Bridgeplate (15mm Studio) is an ARRI standard bridge plate with 15mm studio offset spacing (rods spaced 100mm center to center). New design allows the Bridgeplate to be converted from RED® standard height to ARRI standard height making it compatible with any type of camera rig. Rubberized top coating prevents twisting and slotted design accommodates non-standard screw spacings. Combine with Unified Baseplates for correct rod height on cameras. Includes: (2) 3/8-16 screws (2) 1/4-20 screws Specifications: Weight: 453.592 g (1 lb) Dimensions: 50.8 x 127 x 177.8 mm ( 2 x 5 x 7 in) Unified Baseplate Overview: Rod Standards Tutorial:

WC Pro Gold Mount (Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro) is a metal power plate, created in partnership with Anton Bauer, and has a rugged aluminum body for durability and secure battery mounting and a DC connector compatible with the Blackmagic Pocket Cinema Camera 4K, 6K, 6K G2, and 6K Pro. Features 3x D-Taps for accessory power at battery voltage (12-16V), a digital fuse with reset button, rear cover plate, and captive mounting screws. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. Cable exits the right side of the plate allowing neat looping and insertion into the camera. Length allows minimal cable excess while still being able to reach positions further away from the camera as necessary. For an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW) , Rod Clamp (15mm Studio) , and Rod Clamp (19mm) . Cable length: 16 inches (406.4mm) Specifications: Weight: 187g (0.4 lbs) Dimensions: 142.6 x 92.1 x 21.9 mm (5.6 x 3.6 x 0.9 in) Custom lengths up to 6ft available at the same price. Send us an email with your requirements: info@woodencamera.com Pro Power Plates Overview:

WC Pro V-Mount (Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro) is a metal power plate, created in partnership with Anton Bauer, and has a rugged aluminum body for durability and secure battery mounting and a DC connector compatible with the Blackmagic Pocket Cinema Camera 4K, 6K, 6K G2, and 6K Pro. Features 3x D-Taps for accessory power at battery voltage (12-16V), a digital fuse with reset button, rear cover plate, and captive mounting screws. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. Cable exits the right side of the plate allowing neat looping and insertion into the camera. Length allows minimal cable excess while still being able to reach positions further away from the camera as necessary. For an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW) , Rod Clamp (15mm Studio) , and Rod Clamp (19mm) . Cable length: 16 inches (406.4mm) Specifications: Weight: 187g (0.4 lbs) Dimensions: 142.6 x 92.1 x 21.9 mm (5.6 x 3.6 x 0.9 in) Custom lengths up to 6ft available at the same price. Send us an email with your requirements: info@woodencamera.com Pro Power Plates Overview:

Micro Battery Slide Pro (Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro, V-Mount) utilizes an Anton/Bauer micro battery plate which provides unregulated 14v to a 2-Pin connector for camera power. The 2-Pin connector is compatible with both Blackmagic Pocket Cinema Camera 6K Pro and Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 cameras. The plate attaches via two 15mm rods and position can be adjusted along the battery slide. The user retains the ability to hot swap between the onboard Sony NPF-Series and external cinema battery. The Micro Battery Slide Pro is compatible with both micro and full-sized cinema batteries. It also features 2x D-Tap (5.8 Amps) port for accessory power as well as a digital fuse which cuts off accessory outputs, should the user exceed the set current for accessories, while leaving the camera powered. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. Specifications: Weight: 315 g (0.69 lbs) Dimensions: 145 x 115 x 40 mm (5.7 x 4.5 x 1.5 in)

Micro Battery Slide Pro (Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro, Gold Mount) utilizes an Anton/Bauer micro battery plate which provides unregulated 14v to a 2-Pin connector for camera power. The 2-Pin connector is compatible with both Blackmagic Pocket Cinema Camera 6K Pro and Blackmagic Pocket Cinema Camera 4K / 6K / 6K Pro G2 cameras. The plate attaches via two 15mm rods and position can be adjusted along the battery slide. The user retains the ability to hot swap between the onboard Sony NPF-Series and external cinema battery. The Micro Battery Slide Pro is compatible with both micro and full-sized cinema batteries. It also features 2x D-Tap (5.8 Amps) port for accessory power as well as a digital fuse which cuts off accessory outputs, should the user exceed the set current for accessories, while leaving the camera powered. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. Specifications: Weight: 315 g (0.69 lbs) Dimensions: 145 x 115 x 40 mm (5.7 x 4.5 x 1.5 in)

Blackmagic Pocket Cinema Camera 6K G2 / 6K Pro Unified Accessory Kit (Advanced) is a camera support package designed for the Blackmagic Pocket Cinema Camera 6K G2 and 6K Pro cameras. The BMPCC 6K Pro accessory package features our Blackmagic Pocket Cinema Camera 6K Pro Camera Cage - a form fitting camera cage for secure camera accessory attachment, the compact Top Handle (3/8-16) , LW 15mm Baseplate for BMPCC6K Pro - a quick release baseplate that holds two 15mm rods at the correct lens height, Safety Dovetail (8") which interfaces with the ARRI dovetail slot on the bottom of the Unified Baseplate, and two 15mm Rods (12”) . Included items: Top Handle (3/8-16) Blackmagic Pocket Cinema Camera 6K Pro Camera Cage LW 15mm Baseplate (Blackmagic Pocket Cinema Camera 6K Pro) 2x 15mm Rod (12") Safety Dovetail (8") Specifications: Weight: 2267.96 g (5 lbs) Dimensions: 455 x 170 x 120 mm (17.7 x 6.6 x 4.7 in)

Blackmagic Pocket Cinema Camera 6K G2 / 6K Pro Unified Accessory Kit (Pro, V-Mount) is a camera support package designed for the Blackmagic Pocket Cinema Camera 6K G2 and 6K Pro cameras. The BMPCC 6K Pro unified accessory package features our Blackmagic Pocket Cinema Camera 6K Pro Camera Cage - a form fitting camera cage for secure camera accessory attachment, the compact Top Handle (3/8-16) , LW 15mm Baseplate for BMPCC6K Pro - a quick release baseplate that holds two 15mm rods at the correct lens height, Safety Dovetail (12") which interfaces with the ARRI dovetail slot on the bottom of the LW 15mm Baseplate, two 15mm Rods (15”) , and the Micro Battery Slide Pro . Included items: - Top Handle (3/8-16) - Blackmagic Pocket Cinema Camera 6K Pro Camera Cage - LW 15mm Baseplate (Blackmagic Pocket Cinema Camera 6K Pro) - Micro Battery Slide Pro (Blackmagic Pocket Cinema Camera 6K Pro, V-Mount) - 2x 15mm Rod (15") - Safety Dovetail (12") Specifications: Weight: 2267.96 g (5 lbs) Dimensions: 455 x 170 x 120 mm (17.7 x 6.6 x 4.7 in)

Blackmagic Pocket Cinema Camera 6K G2 / 6K Pro Unified Accessory Kit (Pro, Gold Mount) is a camera support package designed for the Blackmagic Pocket Cinema Camera 6K G2 and 6K Pro cameras. The BMPCC 6K Pro unified accessory package features our Blackmagic Pocket Cinema Camera 6K Pro Camera Cage - a form fitting camera cage for secure camera accessory attachment, the compact Top Handle (3/8-16) , LW 15mm Baseplate for BMPCC6K Pro - a quick release baseplate that holds two 15mm rods at the correct lens height, Safety Dovetail (12") which interfaces with the ARRI dovetail slot on the bottom of the LW 15mm Baseplate, two 15mm Rods (15”) , and the Micro Battery Slide Pro . Included items: - Top Handle (3/8-16) - Blackmagic Pocket Cinema Camera 6K Pro Camera Cage - LW 15mm Baseplate (Blackmagic Pocket Cinema Camera 6K Pro) - Micro Battery Slide Pro (Blackmagic Pocket Cinema Camera 6K Pro, Gold Mount) - 2x 15mm Rod (15") - Safety Dovetail (12") Specifications: Weight: 2267.96 g (5 lbs) Dimensions: 455 x 170 x 120 mm (17.7 x 6.6 x 4.7 in)

D-Tap to Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro (20") allows you to power the BMPCC4K or BMPCC6K using any V-Mount or Gold Mount battery with a D-Tap plug. Cable length: 20 inches (508mm) Specifications: Weight: 22.7g (0.05 lbs) Dimensions: 559 x 25.8 x 11.6 mm (22 x 1.0 x 0.5 in)

Power Extension for Blackmagic Pocket Cinema Camera 4K / 6K / 6K Pro / 6K Pro G2 (Straight, 36") is a power cable that extends any Blackmagic Pocket Cinema Camera 4K / 6K battery plate or AC adapter by 36 inches (0.91 meters). Specifications: Weight: 63g (0.09 lbs) Dimensions: 973 x 9.7 x 9.7 mm (38.3 x 0.38 x 0.38 in)

Blackmagic Pocket Cinema Camera 6K G2 / 6K Pro Camera Cage is a feature-rich camera cage designed exclusively for the Blackmagic Pocket Cinema Camera 6K G2 and 6K Pro cameras. The cage wraps around three sides of the camera, leaving the handgrip exposed for accessibility. The custom cage design offers added support and stability while providing an array of industry-standard 1/4"-20 and 3/8"-16 mounting points along the top and side of the cage. Two 3/8"-16 mounting points can be found on the front of the cage for adding top rod configurations. All mounting points feature a Wooden Camera standard locating hole pattern which is compatible with ARRI standard locating pin accessories. The cage also features several pass-through slots for improved cable management, engraved markings to indicate the camera’s focal plane, and an offset cold shoe mount for adding on-camera lights, microphones, and more. Also included on the side of the cage is a detachable HDMI and USB-C Support Bracket for ensuring secure cable connections. If lightweight 15mm rod support is desired, the cage may be combined with our LW 15mm Baseplate (Blackmagic Pocket Cinema Camera 6K Pro / 6K Pro G2) to provide pass through rod support (sold separately). Included items: - Right Angle HDMI Adapter Specifications: Weight: 361g (.79 lbs) Dimensions: 103 x 143 x 142 mm (4.06 x 5.63 x 5.6 in)

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Rosette Side Plate (URSA Mini, URSA Mini Pro / 12K) attaches to the right side of the Blackmagic URSA Mini and URSA Mini Pro /12K cameras by the ARRI rosette to add additional 1/4-20 and 3/8-16 mounting points. An ARRI standard rosette is available for attaching the handgrip or extension arm. ARRI accessory mount also available in several places (3/8-16 screw hole with locating pins adjacent). Specifications: Weight: 136 g (0.3 lbs) Dimensions: 101.6 x 101.6 x 25.4 mm ( 4 x 4 x 1 in) URSA Mini Side Plates:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. WC Pro Gold Mount (4pin XLR Right Angle) is a metal power plate, created in partnership with Anton Bauer, and has a rugged aluminum body for durability and secure battery mounting and a right angle 4pin XLR. Compatible with Digital Bolex, Blackmagic Studio Camera, Sony F55/F5, Canon C500mkII and many more. Features 3x D-Taps for accessory power at battery voltage (12-16V), a digital fuse with reset button, rear cover plate, and captive mounting screws. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. 16" cable exits the right side of the plate allowing easy insertion into the camera. Custom lengths available up to 6ft for no additional charge. Additional lengths available as needed. Send us an email with your requirements: info@woodencamera.com For an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW) , Rod Clamp (15mm Studio) , and Rod Clamp (19mm) . The orientation of Right Angle XLR connectors can be repositioned following these instructions. Specifications: Weight: 186g (0.41 lbs) Dimensions: 146.1 x 76.2 x 19.1 mm (5.75 x 3 x 0.75 in) Pro Power Plates Overview:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. WC Pro V-Mount (4pin XLR Right Angle) is a metal power plate, created in partnership with Anton Bauer, and has a rugged aluminum body for durability and secure battery mounting and a right angle 4pin XLR. Compatible with Digital Bolex, Blackmagic Studio Camera, Sony F55/F5, Canon C500mkII and many more. Features 3x D-Taps for accessory power at battery voltage (12-16V), a digital fuse with reset button, rear cover plate, and captive mounting screws. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. 16" cable exits the right side of the plate allowing easy insertion into the camera. Custom lengths available up to 6ft for no additional charge. Additional lengths available as needed. Send us an email with your requirements: info@woodencamera.com For an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW) , Rod Clamp (15mm Studio) , and Rod Clamp (19mm) . The orientation of Right Angle XLR connectors can be repositioned following these instructions. Specifications: Weight: 186g (0.41 lbs) Dimensions: 146.1 x 76.2 x 19.1 mm (5.75 x 3 x 0.75 in) Pro Power Plates Overview:

D-Box (URSA Mini, URSA Mini Pro / 12K, Gold Mount) is a custom version of our popular D-Box that adds power distribution, standardized remote start/stop, and hot swap capability to the Blackmagic URSA Mini Pro / 12K, EF Mount, PL Mount, and B4 Mount cameras. The D-Box attaches directly to the back of the camera body using a special Molex connector eliminating external cabling. It also interfaces with the rear LANC port which is how the D-Box controls the camera's run/stop. Connectors on the D-Box are contoured inline with the URSA Mini body, streamlining port connections and cable management. The module also provides two 3pin Fischer ports, allowing start/stop with any ARRI standard trigger device. The D-Box is equipped with a Mini 4pin XLR DC Input and includes a Mini 4pin XLR to Full 4pin XLR pigtail cable allowing an AC power supply or external power plate to be connected to power the camera and accessories during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the battery fully charged. The OEM AC Power Supply provided with the URSA Mini Pro does not have a high enough amperage rating to power a D-box with accessories or perform a Hot Swap from battery power to DC input. Wooden Camera offers a higher rated unit for these requirements: 15V Power Supply (4pin XLR Female) . Overview: Authentic Anton Bauer Gold Mount plate provides 2x D-Tap (unregulated) on the power plate itself but we should note that one D-Tap may be obscured by the right side BNC connectors when in use. The camera receives an unfused connection to the power source and the D-Box connectors share a 7.5A fuse. When using D-Box battery modules it is important to know what amount of power your batteries are capable of providing. Most high-end cinema batteries can supply up to 10A with the URSA Mini camera generally consuming 3-4A in standard configuration. Although the remaining power is available from the D-Taps, 2pin connectors, Fischers, etc., it is best to limit the power draw to 5A or less for best results. Consuming more power than a battery is capable of providing will cause the battery to shut itself off, killing the camera and accessory power. D-Box Connections: 1. D-Tap - 12V Unregulated 2. USB - 5V Regulated 3. 2pin connector - 12V Unregulated - ARRI standard wiring 4. 2pin connector - 12V Unregulated - ARRI standard wiring 5. 3pin Fischer - 24V Regulated - Regulator built in to convert battery voltage to 24V - Maximum 2A continuous (3A surge) shared between the two 3pin Fischers - ARRI standard start/stop capabilities 6. 3pin Fischer - 24V Regulated - Regulator built in to convert battery voltage to 24V - Maximum 2A continuous (3A surge) shared between the two 3pin Fischers - ARRI standard start/stop capabilities 7. DC Input - 12-16V - DC input on the D-Box is a Mini 4pin XLR but a pigtail cable is included to full-size 4pin XLR - Priority is given to DC Input to preserve battery charge when both sources connected Please Note: In addition to the digital or glass fuse governing the output panels of the D-box, his product contains a secondary fuse for the D-tap ports of the attached battery plate. This fuse is located in a fuse holder within the plate and replacements can be purchased here: F10A Fast Blow Fuse D-Box (URSA Mini) Demonstration:

D-Box (URSA Mini, URSA Mini Pro / 12K, V-Mount) is a custom version of our popular D-Box that adds power distribution, standardized remote start/stop, and hot swap capability to the Blackmagic URSA Mini Pro / 12K, EF Mount, PL Mount, and B4 Mount cameras. The D-Box attaches directly to the back of the camera body using a special Molex connector eliminating external cabling. It also interfaces with the rear LANC port which is how the D-Box controls the camera's run/stop. Connectors on the D-Box are contoured inline with the URSA Mini body, streamlining port connections and cable management. The module also provides two 3pin Fischer ports, allowing start/stop with any ARRI standard trigger device. The D-Box is equipped with a Mini 4pin XLR DC Input and includes a Mini 4pin XLR to Full 4pin XLR pigtail cable allowing an AC power supply or external power plate to be connected to power the camera and accessories during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the battery fully charged. The OEM AC Power Supply provided with the URSA Mini Pro does not have a high enough amperage rating to power a D-box with accessories or perform a Hot Swap from battery power to DC input. Wooden Camera offers a higher rated unit for these requirements: 15V Power Supply (4pin XLR Female) . Overview: Authentic IDX V-Mount plate provides 2x D-Tap (unregulated) on the power plate itself but we should note that one D-Tap may be obscured by the right side BNC connectors when in use. The camera receives an unfused connection to the power source and the D-Box connectors share a 7.5A fuse. When using D-Box battery modules it is important to know what amount of power your batteries are capable of providing. Most high-end cinema batteries can supply up to 10A with the URSA Mini camera generally consuming 3-4A in standard configuration. Although the remaining power is available from the D-Taps, 2pin connectors, Fischers, etc., it is best to limit the power draw to 5A or less for best results. Consuming more power than a battery is capable of providing will cause the battery to shut itself off, killing the camera and accessory power. D-Box Connections: 1. D-Tap - 12V Unregulated 2. USB - 5V Regulated 3. 2pin connector - 12V Unregulated - ARRI standard wiring 4. 2pin connector - 12V Unregulated - ARRI standard wiring 5. 3pin Fischer - 24V Regulated - Regulator built in to convert battery voltage to 24V - Maximum 2A continuous (3A surge) shared between the two 3pin Fischers - ARRI standard start/stop capabilities 6. 3pin Fischer - 24V Regulated - Regulator built in to convert battery voltage to 24V - Maximum 2A continuous (3A surge) shared between the two 3pin Fischers - ARRI standard start/stop capabilities 7. DC Input - 12-16V - DC input on the D-Box is a Mini 4pin XLR but a pigtail cable is included to full-size 4pin XLR - Priority is given to DC Input to preserve battery charge when both sources connected Please Note: In addition to the digital or glass fuse governing the output panels of the D-box, his product contains a secondary fuse for the D-tap ports of the attached battery plate. This fuse is located in a fuse holder within the plate and replacements can be purchased here: F10A Fast Blow Fuse D-Box (URSA Mini) Demonstration:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Unified VCT Wedge Plate is a Sony VCT-14 standard device that interfaces with the bottom of all Unified Baseplates. Our special reduced height ARRI dovetail shape allows each Unified camera rig to be quickly installed and balanced properly over your shoulder. Safety pin and stopper screws on the ends prevent accidental removal. Threaded M6 ARRI standard rosettes are found on each side and can be combined with our Rosette Standoffs and Rosette Arms for a quick, handheld configuration. Also present are 1/4-20 threaded holes and the ARRI standard accessory mounts (3/8-16 threaded hole with locating pins adjacent). At the rear of the wedge plate, a knob is present which can be tightened after installing onto the VCT-14 Tripod Plate to prevent any potential wiggle. A key slot is also present on the top center for times when you might need to attach the Wedge Plate directly to the camera bottom using the included 1/4-20 and 3/8-16 low profile screws. Included: (2) 1/4-20 Low Profile Screws (2) 3/8-16 Low Profile Screws Specifications: Weight: 610g (1.3 lbs) Dimensions: 50.8 x 101.6 x 254 mm ( 2 x 4 x 10 in) Unified System and VCT Overview: NAB 2016: Wooden Camera Unified VCT System from Dan Chung

IN STOCK Complete purchase by 3pm CST and order will ship same business day. The Universal Viewfinder Mount (NATO Jaws Only) is just the clamping NATO Jaws found on the complete UVF Mount (NATO Jaws) System. It is great for attaching EVFs like the SmallHD Sidefinder to an existing UVF kit. Specifications: Weight: 90.7 g (0.2 lbs) Dimensions: 50.8 x 76.2 x 25.4 mm ( 2 x 3 x 1 in)

4 pin XLR male connector to 4 pin XLR female. Power rated connectors and cable. Ideal for use with block batteries and camera 4pin XLR adapter cables. Cable measures 10 feet (3 m). Specifications: Weight: 362.8 g (0.8 lbs) Dimensions: 25.4 x 127 x 203.2 mm (1 x 5 x 8 in)

IN STOCK Complete purchase by 3pm CST and order will ship same business day. 18" ARRI standard dovetail with stopper screw on one end and safety latch on the other to prevent accidental camera removal. Arca Swiss standard dovetail on bottom. Threaded 1/4-20 and 3/8-16 holes for accessory mounting and tripod attachment. Attach to Shoulder Pad for custom handheld configurations Perfect for Manfrotto, Miller, Cartoni, Really Right Stuff and more. Specifications: Weight: 572g (1.3 lbs) Dimensions: 18.0 x 2.7 x 0.5 in Bridgeplates, Dovetails, & Dovetail Clamp Overview:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. 19mm diameter iris rods used for mounting accessories like follow focus, matte box, lens support, servo motors, and more. ** Sold as single rods. If a pair of rods are required, add two to cart. ** Available in lengths 3" (142900), 6" (143000), 9" (143100), 12" (143200), 15" (143300), 18" (143400), 24" (143500) Weight: 3": 50g (0.11lb) 6": 98g (0.215lb) 9": 148g (0.325lb) 12": 198g (0.435lb) 15": 384g (0.845lb) 18": 460g (1.02lb) 24": 622g (1.37lb) Rod Standards Tutorial:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Lens Adapter Foot (1/4-20) attaches to the bottom of our all Wooden Camera MFT to PL Adapters and E-Mount to PL Adapters. Includes: (2) M3 x 12mm Phillips (2) M4 x 20mm socket cap Specifications: Weight: 45.3 g (0.1 lbs) Dimensions: 50.8 x 76.2 x 25.4 mm ( 2 x 3 x 1 in)

UVF Mount (ARRI Rosette, Adapter Only) includes only the item that adapts the Zacuto Gratical, F&V SpectraHD 4 EVF, or any other EVF/LCD based on an ARRI rosette to our UVF Mount v2. If full kit is needed, choose UVF Mount (ARRI Rosette) . Specifications: Weight: 45.3 g (0.1 lbs) Dimensions: 101.6 x 101.6 x 25.4 mm ( 4 x 4 x 1 in)

UVF Mount (Rod/NATO Rail) is a version of our popular UVF Mount v2 without the 15mm Tube Clamp portion or Sled. This kit works great with NATO Handle (Plus) which has an integrated 15mm clamp. This kit would typically be used with the UVF v2 Sled or RED® Spinner Mount. Safety pin prevents accidental removal. UVF v2 Sled can attach directly to any NATO-style rail. NATO Arm length approximately 4" Specifications: Weight: 222g (0.5 lbs) Dimensions: 169.9 x 21.6 x 15.6 mm (6.7 x 0.9 x 0.6 in)

Rearward side mounting plate for Blackmagic URSA Camera. Attaches over HD-SDI identification plate to expand mounting surface for accessories and provide attachment points for Universal Wireless Side Plate which is used to attach wireless audio receivers, etc. Array of 1/4-20 and 3/8-16 holes in standard spacing. Includes: (1) M3 x 20mm socket cap screw (1) M3 x 16mm socket cap screw Specifications: Weight: 45.3 g (0.1 lbs) Dimensions: 50.8 x 101.6 x 25.4 mm ( 2 x 4 x 1 in) Sideplate Adapters for Blackmagic URSA Blackmagic URSA Camera Accessory Kit Configuration Guide

IN STOCK Complete purchase by 3pm CST and order will ship same business day. MFT to PL Adapter (Pocket) is a micro four thirds lens mount adapter that enables mounting of all PL mount lenses onto the Blackmagic Design Pocket Cinema Camera. The Adapter includes a foot for attaching to a tripod directly eliminating strain on the camera. The foot can also attach directly to the Pocket Cage by two included screws. PL Cap included to prevent dust from entering sensor area when lens is not attached. This adapter will also work with any MFT camera like the BMCC MFT, GH3, AF100, etc. Features: - 1/4-20 foot for attaching tripod plate or support Includes: (2) M4x20mm socket cap screw Specifications: Weight: 241g (0.5 lbs) Dimensions: 83.6 x 81.5 x 52.6 mm (3.3 x 3.2 x 2.1 in)

IN STOCK Complete purchase by 3pm CST and order will ship same business day. 24 inch ARRI standard dovetail with safety catches on each end. Attaches natively to: O'Connor 2060 O'Connor 2575 O'Connor 120EX Sachtler Cine 30 Specifications: Weight: 1220g (2.7 lbs) Dimensions: 609.6 x 95.2 x 23 mm (24.0 x 3.7 x 0.9 in) Also attaches to any tripod head via screws. Review by Finner Knows Best Bridgeplates, Dovetails, & Dovetail Clamp Overview

18 inch ARRI standard dovetail with safety catches on each end. Attaches natively to: O'Connor 2060 O'Connor 2575 O'Connor 120EX Sachtler Cine 30 Specifications: Weight: 924g (2.0 lbs) Dimensions: 406.4 x 95.2 x 23 mm (16.0 x 3.7 x 0.9 in) Also attaches to any tripod head via screws. Review by Finner Knows Best Bridgeplates, Dovetails, & Dovetail Clamp Overview

12 inch ARRI standard dovetail with safety catches on each end. Attaches natively to: O'Connor 2060 O'Connor 2575 O'Connor 120EX Sachtler Cine 30 Also attaches to any tripod head via screws. Specifications: Weight: 610g (1.3 lbs) Dimensions: 304.8 x 95.2 x 23 mm (12.0 x 3.7 x 0.9 in) Review by Finner Knows Best Bridgeplates, Dovetails, & Dovetail Clamp Overview:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Mini 3pin XLR Male to Full 3pin XLR Female (20") is an audio cable designed to connect a shotgun microphone or audio mixer to the 48V Mono input of the BMPCC4K and BMPCC6K with a 20 inch cable length.

IN STOCK Complete purchase by 3pm CST and order will ship same business day. 15mm diameter iris rods used for mounting accessories like follow focus, matte box, lens support, servo motors, and more. ** Sold as single rods. If a pair of rods are required, add two to cart. ** Availab le in le ngths 3" (142200), 6" (142300), 9" (142400), 12 " (142500), 15" (142600), 18" (142700), 24" (142800) Weight: 3": 36g (0.08lb) 6": 72g (0.16lb) 9": 110g (0.24lb) 12": 152g (0.335lb) 15": 286g (0.63lb) 18": 350g (0.775lb) 24": 470g (1.04lb) Rod Standards Tutorial:

Quick Release Bridgeplate (19mm) is an ARRI standard bridgeplate with 19mm rod openings. The new design allows the bridgeplate to drop down and lock on, anywhere along an ARRI standard dovetail. A safety catch adds security to the lever release function. Unlock the lever half way to slide on the dovetail or push the release button to allow the lever to move further and release the camera vertically. ARRI standard height makes it compatible with most camera rigs including those using our Unified Baseplates . Rubberized top coating prevents twisting and slotted design accommodates non-standard screw spacings. When combining this Bridgeplate with a RED® DSMC2™ or earlier RED® systems, the lens height will be approximately +3mm too tall. If you need to achieve the correct RED® lens height spacing, please choose our Unified Bridgeplate (19mm) . QR Includes: (2) 3/8-16 screws Specifications: Weight: 420g (0.93 lbs) Dimensions: 101.6 x 152.4 x 31.75 mm (4 x 6 x 1.25 in)

Quick Release Bridgeplate (15mm Studio) is an ARRI standard bridgeplate with 15mm studio offset spacing (rods spaced 100mm center to center). The new design allows the bridgeplate to drop down and lock on, anywhere along an ARRI standard dovetail. A safety catch adds security to the lever release function. Unlock the lever half way to slide on the dovetail or push the release button to allow the lever to move further and release the camera vertically. ARRI standard height makes it compatible with most camera rigs including those using our Unified Baseplates . Rubberized top coating prevents twisting and slotted design accommodates non-standard screw spacings. When combining this Bridgeplate with a RED® DSMC2™ or earlier RED® systems, the lens height will be approximately +3mm too tall. If you need to achieve the correct RED® lens height spacing, please choose our Unified Bridgeplate (15mm Studio) . QR Includes: (2) 3/8-16 screws Specifications: Weight: 420g (0.93 lbs) Dimensions: 101.6 x 152.4 x 31.75 mm (4 x 6 x 1.25 in)

Oconnor Easy Load ARRI Dovetail (2575, 2065, 120EX, 12”) is a 12 inch ARRI standard dovetail with safety latches on each end. New easy-load safety latches allow for smoother camera installation. Provides 1/4-20 and 3/8-16 mounting points as well as mounting points for rack gear to be used on OConnor 120ex heads for driving heavy feature film payloads back and forth for accurate balancing. Also attaches to any tripod head via screws. Attaches natively to: OConnor 2560 OConnot 2575 OConnor 2060 OConnor 2065 OConnor 120EX Specifications: Weight: 758g (1.68 lbs) Dimensions: 365.76 x 95.25 x 25.4 mm (14.4 x 3.75 x 1 in)

Blackmagic Pocket Cinema Camera 6K G2 / 6K Pro Unified Accessory Kit (Base) is a camera support package designed for the Blackmagic Pocket Cinema Camera 6K G2 and 6K Pro cameras. The accessory package features our Blackmagic Pocket Cinema Camera 6K Pro Camera Cage - a form fitting camera cage for secure camera accessory attachment, the compact Top Handle (3/8-16) , and our LW 15mm Baseplate for BMPCC6K Pro - a quick release baseplate that holds two 15mm rods at the correct lens height. Included items: Top Handle (3/8-16) Blackmagic Pocket Cinema Camera 6K Pro Camera Cage LW 15mm Baseplate (Blackmagic Pocket Cinema Camera 6K Pro) 2x 15mm Rod (12") Specifications: Weight: 2267.96 g (5 lbs) Dimensions: 455 x 170 x 120 mm (17.7 x 6.6 x 4.7 in)

Wooden Camera brand Gold Mount plate utilizing an Anton Bauer mount and Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro connector. Cable exits the right side of the plate allowing neat looping and insertion into the camera. Length allows minimal cable excess while still being able to reach positions further away from the camera as necessary. For an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW) , Rod Clamp (15mm Studio) , and Rod Clamp (19mm) . 2x D-Tap ports for accessory power. Cable length: 16 inches (406.4mm) Specifications: Weight: 187g (0.4 lbs) Dimensions: 142.6 x 92.1 x 21.9 mm (5.6 x 3.6 x 0.9 in)

Top Handle (3/8-16) is a compact, lightweight top handle that features an array of 1/4"-20 and 3/8”-16 mounting points with ARRI locating pin compatibility. The minimalist design consists of an ergonomic metal grip that can be attached to any 3/8"-16 mounting point. The handle utilizes a versatile captive 3/8"-16 bolt-on mechanism with removable safety pins for mounting which can be tightened with either a flathead screwdriver, 5/32” Allen, or 4mm Allen Key. Top Handle (3/8-16) is 5.12in (130mm) end to end. Specifications: Weight: 155g (.35 lbs) Dimensions: 130 x 28 x 61 mm (5.12 x 1.11 x 2.41 in)

LW 15mm Baseplate (Blackmagic Pocket Cinema Camera 6K G2 / 6K Pro) is a quick release baseplate that provides lightweight 15mm rod support at the correct lens height. 15mm rods pass through front to back and have two locking thumb screws per side. The baseplate quick releases in two ways, giving the user the option to take the 15mm lightweight rods or to leave them behind. Baseplate features an upper ARCA Swiss standard dovetail with 2x 3/8”-16 screw for attaching to the bottom of the camera. Upper ARCA Swiss standard dovetail slides into the LW 15mm Baseplate core, and includes a safety release button for removal. Engraved arrows assist installing the dovetail in the correct direction. Also features a vertical lens support post system. Lower dovetail slot is ARRI standard for attaching to compatible ARRI dovetails or the included Quick Dovetail. With Quick Dovetail attached, the baseplate and camera combination can be combined with an ARRI standard bridge plate like Quick Release Bridgeplate (19mm) or Quick Release Bridgeplate (15mm Studio) . Specifications: Weight: 369g (0.82 lbs) Dimensions: 90 x 118 x 32 mm (3.6 x 4.7 x 1.3 in)

15V Power Supply for 4pin XLR cameras like Canon C500mkII, Panasonic VariCam and VariCam LT, Sony Venice, Venice 2, F55 and F5, Digital Bolex, Blackmagic URSA, URSA Mini, and Studio Camera, and many more. Also works great with our D-Box Alexa Mini, D-Box C300mkII, and 4pin XLR adapter cables. Plugs into the male 4pin XLR input on the camera and provides up to 10A. Includes selection of US, UK, Europe, or Australia power cable and can accept 120V / 240V A/C input. Compatibility Canon C500mkII - plugs into camera body Panasonic VariCam / VariCam LT - plugs into camera body Sony Venice, Venice 2 / F55 / F5 - plugs directly into camera body or V-Mount power plate included with camera Digital Bolex - plugs into camera body Blackmagic URSA / URSA Mini / Studio Camera - plugs into camera body

IN STOCK Complete purchase by 3pm CST and order will ship same business day. NATO Lock Kit is a quick release set based on a NATO standard rail. The rail portion can bolt into a 1/4-20 or 3/8-16 hole using the included screws. Set screw can also be installed to prevent twisting. The rail is also threaded for 1/4-20 and 3/8-16 so accessories can screw into it. The clamp portion of the kit can also bolt into a 1/4-20 or 3/8-16 hole using the included screws and it is also threaded for 1/4-20 and 3/8-16 so accessories can screw into. Compatible with RED® Swat Rails, Zacuto Z-Rails, and many 3rd party NATO products. Specifications: Weight: 50g (0.1 lbs) Dimensions: 47.2 x 47.2 x 18.3 mm (1.9 x 1.9 x 0.7 in)

IN STOCK Complete purchase by 3pm CST and order will ship same business day. D-Box power pigtail cable replacement. Adapts mini 4pin XLR (female) to standard 4pin XLR (male). Cable length is 8 inches (20.3 cm). Wiring also compatible with TV Logic monitors and Alphatron EVF. Heavy gauge wires can withstand more than 10A at 14.4V. Specifications: Weight: 90.7 g (0.2 lbs) Dimensions: 25.4 x 127 x 152.4 mm (1 x 5 x 6 in)

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Top Plate (URSA Mini, URSA Mini Pro / 12K) is a top mounting cheese plate for Blackmagic URSA Mini and URSA Mini Pro / 12K cameras. Attaches to camera top by (4) 1/4-20 screws. Arrays of 1/4-20 holes in standard 9mm spacing and multiple 3/8-16 holes for large accessories. ARRI accessory mount also available in several places (3/8-16 screw hole with locating pins adjacent). Includes tape hook for accurate focus measuring. Original Blackmagic handle can be reinstalled on the Top Plate using center 1/4-20 threaded holes. Includes: (4) 1/4-20 socket cap screws Specifications: Weight: 181.4 g (.5 lbs) Dimensions: 12.7 x 127 x 152.4 mm (0.5 x 5 x 6 in) Camera Configuration Guides: Blackmagic URSA Mini Camera Accessory Kit (Pro)

Unified Baseplate (Sony FX6, Rialto, URSA Mini, Mini Pro, Mini Pro 12K) is a quick release baseplate that provides lightweight 15mm rod support at the correct lens height. 15mm rods pass through front to back and have two locking thumbscrews per side. The baseplate quick releases in two ways, giving the user the option to take the 15mm lightweight rods or to leave them behind. To remove the camera and leave the LW 15mm rods behind, unlock the right side thumbscrew, slide the camera backwards a short distance, and lift straight up. The dovetail attached to the bottom of the camera is an ARCA Swiss standard shape which can integrate with many third party products. Additionally, there are threaded 1/4-20 holes on the bottom for attaching to gimbals or tripod plates when necessary. Also on this upper dovetail is a vertical 15mm rod opening which can be used to support a lens adapter foot directly in front of the camera body. The bottom of the baseplate is comprised of the Lower Quick Dovetail which has 1/4-20 and 3/8-16 threaded holes for attaching to tripod plate or ARRI standard bridgeplate such as Unified Bridgeplate (19mm) or Unified Bridgeplate (15mm Studio) . To remove the camera from the included Lower Quick Dovetail and take the 15mm lightweight rods with you, unlock the left thumbscrew, slide the baseplate backwards a short distance, and lift up. This action exposes an integrated ARRI dovetail slot on the bottom which can attach directly to any 2060 Dovetails , Safety Dovetails , or Shoulder Rigs . For VCT-14 compatible mounting options, the Unified Baseplate can be attached to the Unified VCT Wedge Plate , providing easy counterbalance ability while on the shoulder. This could then be attached to the Unified VCT-14 Tripod Plate which would be attached to the tripod head. Additional Unified Lower Quick Dovetails can be puchased to mount to gimbals, jibs, cranes, etc, making for quick and repeatable camera transitions. ** The Unified Baseplate is backwards compatible with our original Quick Dovetail (Standard) and Quick Dovetail (DSLR, Large) ** Includes: (2) 1/4-20 low profile screw (2) 3/8-16 low profile screw Specifications: Weight: 362.8 g (0.8 lbs) Dimensions: 50.8 x 152.4 x 152.4 mm ( 2 x 6 x 6 in) Unified Baseplate Overview:

Unified Baseplate Camera Dovetail (Sony FX6, Rialto, URSA Mini, Mini Pro, Mini Pro 12K) is a plate which can attach to the base of those cameras and when combined with the Unified Baseplate Core Unit (No Dovetails) , provides 15mm lightweight rods at the correct lens height. The slotted design allows multiple included 1/4-20 and 3/8-16 screws to be attached to the camera bottom up to 70mm apart center to center and non-slip, rubber surface prevents the camera from twisting. The bottom portion of this Unified Camera Dovetail features an ARCA Swiss standard dovetail shape, our patented serrated dovetail design, and 1/4-20 threaded holes for attaching to gimbal mounts and other devices. Additionally the 15mm vertical rod opening can be combined with our Unified Lens Adapter Support Kit components to attach adapters like Wooden Camera, Metabones, etc. securely onto a camera body. Included: (2) 1/4-20 low profile screws (2) 3/8-16 low profile screws Specifications: Weight: 90.7 g (0.2 lbs) Dimensions: 152.4 x 76.2 x 25.4 mm (6 x 3 x 1 in) Unified Baseplate Overview:

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Quick release clamp for Safety NATOs. Great for attaching monitors, handles, and more. Specifications: Weight: 50g (0.1 lbs) Dimensions: 47.2 x 47.2 x 18.3 mm (1.9 x 1.9 x 0.7 in)

8" ARRI standard dovetail with safety catch on one end to prevent accidental camera removal. Threaded 1/4-20 and 3/8-16 holes for accessory mounting and tripod attachment. Attach to Shoulder Pad for custom handheld configurations Perfect for Manfrotto, Miller, Cartoni, and more. Specifications: Weight: 292g (0.6 lbs) Dimensions: 203.2 x 68.2 x 13.2 mm (8.0 x 2.7 x 0.5 in) Bridgeplates, Dovetails, & Dovetail Clamp Overview:

NATO standard, 70mm long, quick release rail attaches to any two 1/4-20 holes up to 42mm apart center to center and provides a mount for NATO Handles and NATO Clamps. Spring loaded pins on each end to prevent accidental accessory removal. Compatible RED® and third party NATO style accessories. Includes: (2) 1/4-20 x 3/8" screws Specifications: Weight: 33g (0.1 lbs) Dimensions: 70.4 x 20.5 x 16.4 mm (2.8 x 0.8 x 0.6 in)