Expand your handheld game by adding Side Grips to your setup. These grips include cold shoe mounts at the top of each handle, allowing you to mount accessories like mics for those compact shooting scenarios. The lightweight grips include ⅜”-16 and ¼”-20 mounting points on the outside of the grips to allow for mounting any additional accessories. Included Items: Ultra Handle Side Offset - Top Right Ultra Handle Side Offset - Bottom Right Ultra Handle Side Offset - Top Left Ultra Handle Side Offset - Bottom Left 2 x Ultra Handle 4” 3/16” Hex Key Specifications: 95 g (0.2 lbs) | 53 x 33 x 97 mm (2.1 x 1.3 x 3.8 in)

Add ⅜”-16 and ¼”-20 mounting points on the sides of your build by attaching these sleek, lightweight Side Rails. These rails give users the flexibility to mount accessories like Bolt-On Rods for lens motors and 25mm Bolt-On Rosettes on either side of the camera. Can be used as a stand-alone accessory or in addition to the Rear Cage and Top Cheese Plate to give users a complete Cage System, these side rails were made to give KOMODO® and KOMODO-X™ users much-needed real estate for adding accessories. The side rails are designed to be compatible with the Adapter Support Brackets for RED’s KOMODO RF to PL lens mount with their forward facing M4 holes. For KOMODO: Left side Rail does cover up the audio ports Microphone and Headphones. Included Items: Side Rail - Left - RED® KOMODO®, KOMODO-X™ Side Rail - Right - RED® KOMODO®, KOMODO-X™ Specifications: Weight: 95 g (0.2 lbs) Dimensions: 53 x 33 x 97 mm ( 2.1 x 1.3 x 3.8 in)

The B-Box enhances the capabilities of the EXT port by offering multiple ports like Run/Stop, timecode, control, and genlock. The B-Box has eight M2.5 threaded holes for additional accessory mounting like Accessory Rails and Bolt-On Plate Adapters. Mounting options included in the B-Box Kit are one 40mm Accessory Rail that is compatible with the Rear Cage mini clamp mount and a Bolt-On 3/8-16 Accessory Mount. This kit includes variations of EXT cables designed for use with our D-Box® for KOMODO-X™ Kit , allowing 24V Run/Stop power out of the 3-pin connector port on the B-Box or to be used directly with the camera's EXT port. Note: For V-RAPTOR and V-RAPTOR [X], user may need a Bolt-On Accessory Plate Adapter or Bolt-On Accessory Rail Clamp for compatibility with their camera cage system. Included Items: B-Box (RED® KOMODO®, KOMODO-X™, V-RAPTOR®) Mini Accessory Rail with Safety (40mm) Bolt-On 3/8-16 Accessory Mount EXT Cable (12-pin 0B Right-Angle Male to 12pin 0B Right-Angle Male, 3in) EXT Cable (9-pin Right-Angle Male to 12-pin Right-Angle Male, 4in) EXT Cable (9-pin Right-Angle Male to 12-pin Straight Male, 12in) EXT Cable (12-pin 0B Straight Male to 12-pin 0B Right Angle Male, 12in) Specifications: Weight: 87g (0.2 lbs) Dimensions: 42 x 30 x 75 mm ( 1.7 x 1.2 x 2.95 in)

Our line of Bolt-On Accessory Plate Adapters were designed to mount accessories that have M2.5 threaded holes to your build, like the Accessory Plate Collection or the B-Box for (KOMODO®, KOMODO-X™, V-RAPTOR®). Available in ⅜”-16 and ¼”-20 mounting screws in both variations of flat and right angle, these universal adapters allow you to add accessories to your build securely. Included Items: 3/16” Hex Key 2mm Hex Key Specifications: Bolt-On Accessory Plate Adapter (Flat, 3/8"-16) : 13 g (0.03 lbs) | 28 x 29.5 x 9.5 mm (1.1 x 1.2 x 0.4 in) Bolt-On Accessory Plate Adapter (Flat, 1/4"-20) : 13 g (0.03 lbs) | 28 x 29.5 x 9.5 mm (1.1 x 1.2 x 0.4 in) Bolt-On Accessory Plate Adapter (RA, 3/8"-16) : 14 g (0.03 lbs) | 24.5 x 29.5 x 16 mm (0.97 x 1.2 x 0.04 in) Bolt-On Accessory Plate Adapter (RA, 1/4"-20): 14 g (0.03 lbs) | 24.5 x 29.5 x 16 mm (0.97 x 1.2 x 0.04 in)

The Side Rail - Right gives users mounting points on the right side of the KOMODO® and KOMODO-X™ as well as Sensor Plane markings. This rail offers four ⅜”-16 and two ¼”-20 anti-twist mounting points where you can add accessories like Bolt-On Rods for lens motors or any of our universal accessories. Can work as a standalone item or in tandem with the Rear Cage and Side Rail - Left , this system together was designed to provide all-around rigging for the KOMODO-X. The side rails are designed to be compatible with the Adapter Support Brackets for RED’s KOMODO RF to PL lens mount with their forward facing M4 holes. Included Items: 3mm Hex Key Specifications: Weight: 47.5 g (0.10 lbs) Dimensions: 53 x 16.5 x 97 mm (2.1 x 0.65 x 3.8 in)

The Side Rail - Left gives users mounting points on the left side of the KOMODO® or KOMODO-X™ as well as Sensor Plane markings. This rail offers four ⅜”-16 and two ¼”-20, anti-twist mounting points where you can add accessories like Bolt-On Rods for lens motors or any of our universal accessories. Can work as a standalone item or in tandem with the Rear Cage and Side Rail - Right , this system together was designed to provide all-around rigging for the KOMODO-X. The side rails are designed to be compatible with the Adapter Support Brackets for RED’s KOMODO RF to PL lens mount with their forward facing M4 holes. Included Items: 3mmHex Key Specifications: Weight: 47.5 g (0.10 lbs) Dimensions: 53 x 16.5 x 97 mm (2.1 x 0.65 x 3.8 in)

The Ultra Handle 4” Kit comes with the Ultra Handle Upright for RED® DSMC3™, a 4” extension, and a 1” extension. The upright has a 3-pin connector to allow Run/Stop functionality and includes dual ¼”-20, anti-twist screws for mounting to the Top Cheese Plate, RED® RMI adapter or directly to the camera. The handle includes multiple ⅜”-16 and ¼”-20, anti-twist mounting points throughout for mounting additional accessories. Included Items: 1” Ultra Handle Extension 4” Ultra Handle Extension 3/16" Hex T Handle Ultra Handle Upright for RED® DSMC3™ Specifications: Weight: 234 g (0.5 lbs) Dimensions: 152 x 63.7 x 70 mm (6 x 2.5 x 0.75 in)

The Top Cheese Plate securely mounts to the KOMODO® or KOMODO-X™ using two ¼”-20 screws with anti-twist pins and adds seven ¼”-20, anti-twist mounting points. The plate connects directly to the top of the camera, allowing the contact pins to pass Run/Stop connection through the plate. This Top Plate can be used in tandem with the Ultra Handle Upright for RED® DSMC3™ as well as the Rigging Top Plate. Included Items: 3/16” Hex Key Specifications: Weight: 52 g (0.11 lbs) Dimensions: 31.4 x 85 x 10.5 mm (1.2 x 3.3 x 0.4 in)

The ARCA Base Plate was designed for dual 15mm LW rods and allows for maintaining optimal lens height for studio-style builds. This Base Plate comes with a quick-release lever to be used with the ARCA Riser when lightweight builds are necessary. This Base Plate includes a Bridge Plate Dovetail for use with either 15mm or 19mm Bridge Plates and tripod plates. Our ARCA system allows quick adjustments from a studio build to a Steadicam or Handheld build in seconds. Included Items: Bridge Plate Dovetail P00109 Specifications: Weight: 337 g (0.75 lbs) Dimensions: 88.25 x 117.5 x 44.5 mm (3.5 x 4.6 x 1.75 in)

The Ultra Handle Upright for the RED® system has the appropriate ¼”-20 spacing for use with KOMODO-X™, KOMODO® and V-RAPTOR® camera s. This Upright includes pogo pins for the 3-pin connector that allows for Run/Stop trigger function. The design also includes six ⅜”-16, anti-twist pin inserts and dual front-facing ¼”-20 screw holes. This Upright is also compatible with the DSMC3™ RED® Touch 7.0” Monitor’s RMI connection. Specifications: Weight: 97.3g (0.21 lbs) Dimensions: 25.4 x 63.7 x 70 mm (1 x 2.5 x 2.75 in)

The Bolt-On Rosettes give users the ability to mount Rosette Handle Grips anywhere on their build. These rosettes have locking pins to prevent twisting and were designed with tool passthrough for secure mounting. The Bolt-On Rosettes come in either ⅜”-16 and ¼”-20 options. Included Items: 4mm Hex Key Specifications: 25mm Bolt-On Rosette (1/4"-20) : 10.3 g (0.02 lbs) | 25 x 25 x 16 mm (1 x 1 x 0.6 in) 25mm Bolt-On Rosette (3/8"-16) : 10.3 g (0.02 lbs) | 25 x 25 x 16 mm ( 1 x 1 x 0.6 in)

The Shoulder Plate - ARCA was made to allow users to quickly swap from studio to handheld setups when using the ARCA Base Plate. This Shoulder Plate is easy to unscrew and slides off the ARCA Base Plate in seconds with one press of the safety release. Users can adjust the plate on the ARCA Base Plate for optimal shoulder pad position. Specifications: 214 g (0.5 lbs) | 180 x 110.5 x 16 mm (7.1 x 4.4 x 0.6 in)

This cable connects from the EXT port of the camera to the D-Box® for KOMODO-X™ system providing Run/Stop abilities to the 3-pin connector port.

These EXT Cables connect from the camera's EXT port to the B-Box for (KOMODO®, KOMODO-X™, V-RAPTOR®) directly, breaking out control options like Timecode, Control, Genlock and 3-pin Run/Stop ability. Two length options of 4” or 12“ were intended to keep your B-Box in the place that works best for the user's needs. The 4” length was designed to be used with the Rear Cage and keeps the build tidy. The 12” length allows users to place the B-Box anywhere that works best for them, this could be along the camera's cage system like Side Rails or 3rd party system options. Please note, the 3-pin port will not provide 24V power in this configuration unless connected to the D-Box® for KOMODO-X. Pre-Order Terms and Conditions

12 inch ARRI standard dovetail with safety catches on each end. Attaches natively to: O'Connor 2060 O'Connor 2575 O'Connor 120EX Sachtler Cine 30 Also attaches to any tripod head via screws. Specifications: Weight: 610g (1.3 lbs) Dimensions: 304.8 x 95.2 x 23 mm (12.0 x 3.7 x 0.9 in) Review by Finner Knows Best Bridgeplates, Dovetails, & Dovetail Clamp Overview:

8" ARRI standard dovetail with safety catch on one end to prevent accidental camera removal. Threaded 1/4-20 and 3/8-16 holes for accessory mounting and tripod attachment. Attach to Shoulder Pad for custom handheld configurations Perfect for Manfrotto, Miller, Cartoni, and more. Specifications: Weight: 292g (0.6 lbs) Dimensions: 203.2 x 68.2 x 13.2 mm (8.0 x 2.7 x 0.5 in) Bridgeplates, Dovetails, & Dovetail Clamp Overview:

12" ARRI standard dovetail with safety catch on one end to prevent accidental camera removal. Threaded 1/4-20 and 3/8-16 holes for accessory mounting and tripod attachment. Attach to Shoulder Pad for custom handheld configurations Perfect for Manfrotto, Miller, Cartoni, and more. Specifications: Weight: 427g (0.9 lbs) Dimensions: 304.8 x 68.4 x 13.4 mm (12.0 x 2.7 x 0.5 in) Bridgeplates, Dovetails, & Dovetail Clamp Overview:

Dovetail Clamp adapts any camera system, baseplate, or accessory to an ARRI standard dovetail. Great for use with our Fixed Bases, Quick Bases, Universal Baseplate, and Riser systems. Includes: (2) Unified Bridgeplate Screw (3/8-16) (2) Unified Bridgeplate Screw (1/4-20) Specifications: Weight: 164g (0.4 lbs) Dimensions: 89.8 x 99 x 18.9 mm (3.5 x 3.9 x 0.7 in) Bridgeplates, Dovetails, & Dovetail Clamp Overview:

A-Box allows for two XLR microphones to be plugged into any camera having a single 3.5mm input (also referred to as 1/8" or mini-jack). This system includes the highest quality professional grade connectors included within the box. Comes with Bolt On 19mm Rod for attaching to any 1/4-20 threaded hole and 15mm Adapter Bushing for clamping to 15mm rods. This adapter does not provide phantom power to connected accessories. Includes: (1) 1/4-20 x 3/8" screw (1) Bolt On 19mm Rod (1) 15mm Adapter Bushing Specifications: Weight: 363g (0.8 lbs) Dimensions: 76 x 76 x 178 mm (3.0 x 3.0 x 7.0 in)

Quick Release Bridgeplate (19mm) is an ARRI standard bridgeplate with 19mm rod openings. The new design allows the bridgeplate to drop down and lock on, anywhere along an ARRI standard dovetail. A safety catch adds security to the lever release function. Unlock the lever half way to slide on the dovetail or push the release button to allow the lever to move further and release the camera vertically. ARRI standard height makes it compatible with most camera rigs including those using our Unified Baseplates . Rubberized top coating prevents twisting and slotted design accommodates non-standard screw spacings. When combining this Bridgeplate with a RED® DSMC2™ or earlier RED® systems, the lens height will be approximately +3mm too tall. If you need to achieve the correct RED® lens height spacing, please choose our Unified Bridgeplate (19mm) . QR Includes: (2) 3/8-16 screws Specifications: Weight: 420g (0.93 lbs) Dimensions: 101.6 x 152.4 x 31.75 mm (4 x 6 x 1.25 in)

Quick Release Bridgeplate (15mm Studio) is an ARRI standard bridgeplate with 15mm studio offset spacing (rods spaced 100mm center to center). The new design allows the bridgeplate to drop down and lock on, anywhere along an ARRI standard dovetail. A safety catch adds security to the lever release function. Unlock the lever half way to slide on the dovetail or push the release button to allow the lever to move further and release the camera vertically. ARRI standard height makes it compatible with most camera rigs including those using our Unified Baseplates . Rubberized top coating prevents twisting and slotted design accommodates non-standard screw spacings. When combining this Bridgeplate with a RED® DSMC2™ or earlier RED® systems, the lens height will be approximately +3mm too tall. If you need to achieve the correct RED® lens height spacing, please choose our Unified Bridgeplate (15mm Studio) . QR Includes: (2) 3/8-16 screws Specifications: Weight: 420g (0.93 lbs) Dimensions: 101.6 x 152.4 x 31.75 mm (4 x 6 x 1.25 in)

LW15mm Baseplate (RED® KOMODO™, KOMODO-X) provides 15mm lightweight rod openings at the correct distance to the center of the lens. ARRI standard M6 rosettes are on both sides along with 1/4-20 threaded holes. 3/8-16 ARRI accessory mount also available on camera-right side. Baseplate features upper ARCA Swiss standard dovetail with center screw channel and vertical lens support post system. Attach one 1/4-20 and 3/8-16 screw to camera bottom and position vertical, 1/4-20 rod post underneath lens adapter like Canon RF to PL Mount Pro (RED® KOMODO™) . Lower dovetail slot is ARRI standard for attaching to ARRI dovetails or the included Quick Dovetail. With Quick Dovetail attached, the baseplate and camera combination can be combined with an ARRI standard bridge plate like Quick Release Bridgeplate (19mm) or Quick Release Bridgeplate (15mm Studio) . Includes: (2) 1/4-20 low profile screws (2) 3/8-16 low profile screws Specifications: Weight: 389 g (0.86 lbs) Dimensions: 114.3 x 101.6 x 58.42 mm (4.5 x 4 x 2.3 in)

Top Mount Only for RED KOMODO-X & KOMODO is a Top Mount that attaches to the camera body using two captive 3/4" screws and provides a center ARCA Swiss dovetail clamping slot along with 1/4-20 and 3/8-16 threaded holes for attaching accessories. Includes 3/4" screws for mounting directly to top of camera as well as one 1/3" screw for attaching on top of the KOMODO™™ Outrigger Handle sold by RED®. Items like Top Handle Only , Monitor Hinge Only , and Top Plate Only (RED® KOMODO™, ARCA Swiss) can be purchased separately and installed into this device. Includes: 2x 3/4" Screws 1x 1/3" Screw Specifications: Weight: 65 g (0.15 lbs) Dimensions: 107.95 x 31.75 x 12.7 mm (4.25 x 1.25 x .5 in)

Top Handle Only for RED KOMODO-X & KOMODO slides into an ARCA Swiss slot like the one found on Top Mount Only (RED® KOMODO™) which is sold separately. When combined with Top Mount, system leaves camera control screen easily accessible. Shoe mount on top can hold on-camera lights and microphones and side 15mm opening can hold an optional UVF Mount V2 . 1/4-20 and 3/8-16 ARRI accessory mount in several places and 15mm lightweight rod bracket on front for attaching lens motors and more. Specifications: Weight: 178 g (0.4 lbs) Dimensions: 139.7 x 114.3 x 57.15 mm (5.5 x 4.5 x 2.25 in)

Monitor Hinge Only for RED KOMODO-X & KOMODO can attach into ARCA slot like the one found on Top Mount Only (RED® KOMODO™) which is sold separately. When combined with Top Mount, system provides a direct 1/4-20 mount for SmallHD monitors . Included rubber pad can be added for attaching third party monitors. A 15mm mounting spud is included and allows monitor arm to be quick released and attached onto Top Handle (RED® KOMODO™) which is also sold separately. Specifications: Weight: 60 g (0.14 lbs) Dimensions: 50.8 x 50.8 x 38.1 mm (2 x 2 x 1.5 in)

Battery Slide Pro Gold Mount (RED® KOMODO™) attaches to the camera-left, BP-9 battery slot and powers the camera using a right angle connector. Thumbscrew can be loosened to tilt and slide the plate as needed. Three D-Taps on the plate provide battery voltage for accessories and power is monitored for over-current. If more than 5.8A are used by accessories, a digital fuse will trip and the red LED will illuminate but the camera will remain powered. Reset button can be pressed once to restart accessory power . DC Input on camera-right side can be used for hot-swapping between block battery and on-board battery. While the AC adapter that comes with the KOMODO™ can be used, please note that it may not be powerful enough to sustain the camera and accessory draw. If hot-swapping between Gold Mount battery and BP-955 battery is desired, please consider Battery Slide Extension for Canon BP-955 Hot Swap (RED® KOMODO™) which moves the battery plate further back from the camera body. Specifications: Weight: 264 g (0.59 lbs) Dimensions: 127 x 114.3 x 44.45 mm (5 x 4.5 x 1.75 in)

Battery Slide Pro V-Mount (RED® KOMODO™ ) attaches to the camera-left, BP-9 battery slot and powers the camera using a right angle connector. Thumbscrew can be loosened to tilt and slide the plate as needed. Three D-Taps on the plate provide battery voltage for accessories and power is monitored for over-current. If more than 5.8A are used by accessories, a digital fuse will trip and the red LED will illuminate but the camera will remain powered. Reset button can be pressed once to restart accessory power. DC Input on camera-right side can be used for hot-swapping between block battery and on-board battery. While the AC adapter that comes with the KOMODO™ can be used, please note that it may not be powerful enough to sustain the camera and accessory draw. If hot-swapping between Gold Mount battery and BP-955 battery is desired, please consider Battery Slide Extension for Canon BP-955 Hot Swap (RED® KOMODO™) which moves the battery plate further back from the camera body. Specifications: Weight: 264 g (0.59 lbs) Dimensions: 127 x 114.3 x 44.45 mm (5 x 4.5 x 1.75 in)

Battery Slide Extension for Canon BP-955 Hot Swap for RED KOMODO-X & KOMODO allows either Battery Slide Pro V-Mount or Gold Mount (RED® KOMODO™) to be positioned further from the camera body to allow hot-swapping between brick battery and BP-955 battery. Please note that only the Canon BP-955 battery is recommended for this configuration as larger capacity batteries may not fit properly between battery plate and back of camera. Specifications: Weight: 35 g (0.08 lbs) Dimensions: 72.4 x 38.1 x 45.7 mm (2.85 x 1.5 x 1.80 in)

B-Box ( RED® KOMODO ™) attaches to the camera-right BP-9 battery slot and provides a breakout for the camera’s EXT connector. Battery Slide Pro V-Mount or Gold Mount for KOMODO can be used simultaneously and custom right-angle compatible connector allows for neat cable run. Canon BP-9 batteries could also be attached in camera-left slot while B-Box is used. Available ports include: - R/S (3pin Fischer) simple run/stop for Handgrip Trigger Box , Simple 3pin Fischer Trigger Cable , etc. no power available devices like ARRI WCU-4 may require CTRL port interface with cable K2.0015758 pin1:GND, pin2:N/C, pin3:GPI - Timecode (5pin) standard wiring for timecode in/out pin1:GND, pin2:LTC-IN, pin3:N/C, pin4:N/C, pin5:LTC-OUT - CTRL (4pin) standard wiring for RED® CTRL pin1:GND, pin2:UART-RX, pin3:GPO, pin4:UART-TX - 5V (USB) 5V available at 500mA maximum power may need to be enabled in camera menu - Genlock (BNC) standard wiring for genlock center:signal, shell:GND Specifications: Weight: 100 g (0.23 lbs) Dimensions: 107.95 x 82.5 x 25.4 mm (4.25 x 3.25 x 1 in)

Canon RF to PL Mount Pro adapts PL lenses to Canon RF Mounts. Flange focus is set to match camera prior to shipping but shims are included should further adjustment be desired. This mount works with RED® cameras such as the V-Raptor™, KOMODO-X, KOMODO™ and Canon cameras such as the Canon EOS C70, C80 and C400. Tabs on PL collar allow for easy lock and unlock and 1/4-20 on mount base allows for lens support to be added like that on the LW 15mm Baseplate (RED® KOMODO™), ARCA Riser Plate for Canon EOS C80, or ARCA Riser Plate for Canon EOS C400. Includes: (3) Vertical lens support posts (Small, Medium, Large) Specifications: Weight: 240 g (0.53 lbs) Dimensions: 95.25 x 95.25 x 57.15 mm (3.75 x 3.75 x 2.25 in)

RED® KOMODO™ Accessory Kit (Advanced) is an accessory kit for RED KOMODO-X & KOMODO that includes the LW 15mm Baseplate , Complete Top Mount Kit , and 2x 15mm Rods (12”) . The LW 15mm Baseplate (RED® KOMODO™) provides 15mm lightweight rod openings at the correct distance to the center of the lens. ARRI standard, M6 rosettes are on both sides along with 1/4-20 threaded holes. 3/8-16 ARRI accessory mount also available on camera right side. Baseplate features upper ARCA Swiss standard dovetail with center screw channel and vertical lens support post system. Attach one 1/4-20 and 3/8-16 screw to camera bottom and position vertical, 1/4-20 rod post underneath lens adapter like Canon RF to PL Mount Pro (RED® KOMODO™) . Lower dovetail slot is ARRI standard for attaching to ARRI dovetails or the included Quick Dovetail . With Quick Dovetail attached, the baseplate and camera combination can be combined with an ARRI standard bridge plate like Quick Release Bridgeplate (19mm) or Quick Release Bridgeplate (15mm Studio) . The Complete Top Mount Kit (RED® KOMODO™) features a Top Mount that attaches to the camera body using two captive 1/4-20 screws and provides a center ARCA Swiss dovetail clamping slot along with 1/4-20 and 3/8-16 threaded holes for attaching accessories. Included Top Handle slides into ARCA slot and leaves camera control screen easily accessible. Shoe mount on top can hold on-camera lights and microphones and side 15mm opening can hold included monitor arm or UVF Mount V2 . 1/4-20 and 3/8-16 ARRI accessory mount in several places and 15mm lightweight rod bracket on front for attaching lens motors and more. Monitor Hinge can attach into ARCA slot and provides a direct 1/4-20 mount for SmallHD monitors . Included rubber pad can be added for attaching third party monitors. A 15mm mounting spud is included and allows monitor arm to be quick released and attached onto Top Handle. Top Plate slides into ARCA slot to provide rows of 1/4-20 and 3/8-16 ARRI accessory mounts in standard spacing and can be adjusted forwards to allow camera control screen access. Great for attaching to gimbal and drone systems or for using legacy Wooden Camera products. Specifications: Weight: 1038 g (2.29 lbs) Dimensions: 304.8 x 158.75 x 63.5 mm (12 x 6.25 x 2.5 in)

RED® KOMODO™ Accessory Kit (Pro, V-Mount) is an accessory kit for RED® KOMODO™ that includes the LW 15mm Baseplate , Complete Top Mount Kit , Battery Slide Pro V-Mount , and 2x 15mm Rods (12”) . The LW 15mm Baseplate (RED® KOMODO™) provides 15mm lightweight rod openings at the correct distance to the center of the lens. ARRI standard, M6 rosettes are on both sides along with 1/4-20 threaded holes. 3/8-16 ARRI accessory mount also available on camera right side. Baseplate features upper ARCA Swiss standard dovetail with center screw channel and vertical lens support post system. Attach one 1/4-20 and 3/8-16 screw to camera bottom and position vertical, 1/4-20 rod post underneath lens adapter like Canon RF to PL Mount Pro (RED® KOMODO™) . Lower dovetail slot is ARRI standard for attaching to ARRI dovetails or the included Quick Dovetail . With Quick Dovetail attached, the baseplate and camera combination can be combined with an ARRI standard bridge plate like Quick Release Bridgeplate (19mm) or Quick Release Bridgeplate (15mm Studio) . The Complete Top Mount Kit (RED® KOMODO™) features a Top Mount that attaches to the camera body using two captive 1/4-20 screws and provides a center ARCA Swiss dovetail clamping slot along with 1/4-20 and 3/8-16 threaded holes for attaching accessories. Included Top Handle slides into ARCA slot and leaves camera control screen easily accessible. Shoe mount on top can hold on-camera lights and microphones and side 15mm opening can hold included monitor arm or UVF Mount V2 . 1/4-20 and 3/8-16 ARRI accessory mount in several places and 15mm lightweight rod bracket on front for attaching lens motors and more. Monitor Hinge can attach into ARCA slot and provides a direct 1/4-20 mount for SmallHD monitors . Included rubber pad can be added for attaching third party monitors. A 15mm mounting spud is included and allows monitor arm to be quick released and attached onto Top Handle. Top Plate slides into ARCA slot to provide rows of 1/4-20 and 3/8-16 ARRI accessory mounts in standard spacing and can be adjusted forwards to allow camera control screen access. Great for attaching to gimbal and drone systems or for using legacy Wooden Camera products. The Battery Slide Pro V-Mount (RED® KOMODO™) attaches to the camera-left, BP-9 battery slot and powers the camera using a right angle connector. Thumbscrew can be loosened to tilt and slide the plate as needed. Three D-Taps on the plate provide battery voltage for accessories and power is monitored for over-current. If more than 5.8A are used by accessories, a digital fuse will trip and the red LED will illuminate but the camera will remain powered. Reset button can be pressed once to restart accessory power. DC Input on camera-right side can be used for hot-swapping between block battery and on-board battery. While the AC adapter that comes with the KOMODO™ can be used, please note that it may not be powerful enough to sustain the camera and accessory draw. If hot-swapping between V-Mount battery and BP-955 battery is desired, please consider Battery Slide Extension for Canon BP-955 Hot Swap (RED® KOMODO™) which moves the battery plate further back from the camera body. Specifications: Weight: 1302 g (2.88 lbs) Dimensions: 304.8 x 158.75 x 63.5 mm (16 x 6.25 x 2.5 in)

Top Plate Only for RED KOMODO-X & KOMODO slides into an ARCA Swiss slot like the one found on Top Mount Only (RED® KOMODO™) which is sold separately. When combined with Top Mount, system provides rows of 1/4-20 and 3/8-16 ARRI accessory mounts in standard spacing and can be adjusted forwards to allow camera control screen access. Great for attaching to gimbal and drone systems or for using legacy Wooden Camera products. Specifications: Weight: 47 g (0.11 lbs) Dimensions: 101.6 x 38.1 x 12.7 mm (4 x 1.5 x .5 in)

D-Tap to RED® KOMODO™ is a D-tap to RED® KOMODO™ cable that allows you to power the camera using any V-Mount or Gold Mount battery with a D-Tap plug. Cable length: 36 inches (91 cm) Specifications: Weight: 74 g (0.17 lbs) Dimensions: 304.8 x 38.6 x 12.3 mm (12 x 1.5 x .5 in)

Power Extension RED® KOMODO™ is a power cable that extends the Komodo battery plate or AC adapter by 36 inches. Cable length: 120 inches (304 cm) Specifications: Weight: 136 g (0.3 lbs) Dimensions: 25.4 x 127 x 203.2 mm (1 x 5 x 8 in)

Timecode In/Out Cable for RED® V-Raptor™, KOMODO-X, KOMODO™ is a female, 5pin to right angle, RED EXT, 9pin. The connector exits toward the operator side, leaving other ports or accessories on the back of the camera accessible. Cable length: 12 inches (30cm) Specifications: Weight: 90 g (0.2 lbs) Dimensions: 25.4 x 127 x 152.4 mm (1 x 5 x 6 in)

Control Cable for RED® V-Raptor™, KOMODO-X, KOMODO™ CTRL is a Female 4pin 00 connector to a right angle, RED® EXT, 9pin. The connector exits toward the operator side, leaving other ports or accessories on the back of the camera accessible. Please note that the RED KOMODO-X & KOMODO utilizes RCP2 protocol so the device being attached may be incompatible or require a firmware update. Cable length: 12 inches (30 cm) Specifications: Weight: 90 g (0.2 lbs) Dimensions: 25.4 x 127 x 152.4 mm (1 x 5 x 6 in)

3pin Fischer Trigger Cable for RED® V-Raptor™, KOMODO-X, KOMODO™ is a Female 3pin Fischer wired in ARRI standard configuration to a right angle, RED® EXT, 9pin. The connector exits toward the operator side, leaving other ports or accessories on the back of the camera accessible. Please note this is for simple triggering only. No power, tally, or any other functionality is available. Cable length: 36 inches (91cm) Specifications: Weight: 90 g (0.2 lbs) Dimensions: 25.4 x 127 x 152.4 mm (1 x 5 x 6 in)

Genlock Cable for RED® V-Raptor™, KOMODO-X, KOMODO™ is a female BNC connector to a right angle, RED EXT, 9pin. The connector exits toward the operator side, leaving other ports or accessories on the back of the camera accessible. Cable length: 12 inches (30 cm) Specifications: Weight: 90 g (0.2 lbs) Dimensions: 25.4 x 127 x 152.4 mm (1 x 5 x 6 in)

Replacement Upper ARCA Dovetail for the LW15mm Baseplate (RED® KOMODO™) also compatible with KOMODO-X . Includes: (1) 1/4-20 low profile screws (1) 3/8-16 low profile screws Specifications: Weight: 38 g (0.09 lbs) Dimensions: 101.6 x 38.1 x 19 mm (4 x 1.5 x .75 in)

RED® KOMODO™, KOMODO-X Revolva Riser provides clearance for the Wooden Camera RED® KOMODO™ Top Mount Kits to be utilized with the KipperTie Revolva RF/PL. Includes: (2) 1/4-20x3/8” Button Specifications: Weight: 24 g (0.06 lbs) Dimensions: 82.55 x 20.32 x 6.35 mm ( 3.25 x .8 x .25 in)

Safety NATO Arm (RED® KOMODO™, KOMODO-X) is a NATO standard side mounting arm for the RED KOMODO-X and KOMODO camera with arrays of 1/4”-20 and 3/8”-16 mounting points in standard spacing provide additional mounting for NATO handles, clamps and accessories. Attaches via M4 screws on either side of the camera featuring spring loaded pins on each end prevent accidental accessory removal. Includes: (2) M4 x 7mm Socket Cap Specifications: Weight: 35 g (0.08 lbs) Dimensions: 95 x 23 x 18 mm ( 3.75 x .91 x .71 in)

Oconnor Easy Load ARRI Dovetail (2575, 2065, 120EX, 12”) is a 12 inch ARRI standard dovetail with safety latches on each end. New easy-load safety latches allow for smoother camera installation. Provides 1/4-20 and 3/8-16 mounting points as well as mounting points for rack gear to be used on OConnor 120ex heads for driving heavy feature film payloads back and forth for accurate balancing. Also attaches to any tripod head via screws. Attaches natively to: OConnor 2560 OConnot 2575 OConnor 2060 OConnor 2065 OConnor 120EX Specifications: Weight: 758g (1.68 lbs) Dimensions: 365.76 x 95.25 x 25.4 mm (14.4 x 3.75 x 1 in)

Available in either 1/4"-20 or 3/8"-16, the Linear Bubble Level can be attached to a single mounting point to provide a portable spirit level for leveling equipment. A single detachable locating pin is utilized to prevent twisting. The 3/8"-16 locating pin is compatible with any ARRI-standard mounting point. The 1/4"-20 locating pin is compatible with both Wooden Camera and ARRI-standard mounting points. Specifications: Weight: 14.6g (0.03 lbs) Dimensions: 34 x 23.3 x 19 mm (1.3 x .92 x 0.75 in)

Available in either 1/4"-20 or 3/8"-16, the Round Bubble Level can be attached to a single mounting point to provide a low-profile spirit level for leveling equipment. Specifications: Round Bubble Level (3/8"-16): 3g (0.007 lbs) 7.5 x 7.5 x 13 mm (0.3 x 0.3 x 0.52 in) Round Bubble Level (1/4"-20): 2g (0.004 lbs) 6.25 x 6.25 x 19 mm (0.25 x 0.25 x 0.25 in)